MechArmor Defense Tac Ops Ambi Charging Handle

More
8 years 11 months ago - 8 years 11 months ago #46581 by jtallen83
MechArmor Defense Tac Ops Ambi Charging Handle was created by jtallen83
I just installed a MechArmor Defense Ambi charging handle in my Sig PM400. Doubt I ever buy anything else. I've got one from Bravo Co. and a Raptor but this is by far the smoothest operating charging handle I have ever felt. I got it for my wife because it looked like it had the biggest, easiest gripping surface There is no slop at all but it glides smooth as a babies butt! It feels solid as a rock, if it had a bit more weight I'd try to drive a nail with it.They make them for both 5.56 and 7.62 with just a few models listed that they do not fit.
mechdefense.com/products/ar15-charging-h...original-for-m4-ar15


This image is hidden for guests.
Please log in or register to see it.
Last edit: 8 years 11 months ago by jtallen83.

Please Log in or Create an account to join the conversation.

More
8 years 11 months ago #46584 by faawrenchbndr
Replied by faawrenchbndr on topic MechArmor Defense Tac Ops Ambi Charging Handle
Is it me or does it like like a lot of snag hazards?

Please Log in or Create an account to join the conversation.

More
8 years 11 months ago #46591 by jtallen83
Replied by jtallen83 on topic MechArmor Defense Tac Ops Ambi Charging Handle

faawrenchbndr wrote: Is it me or does it like like a lot of snag hazards?


They make a CQB version that is narrower for applications where that is an issue. The standard handle really doesn't stick out much more than what is needed to grab it and avoid a scope. I would say it is less snaggable(is that a word?) than the BCM 3 handle I have on my Matrix build.

Please Log in or Create an account to join the conversation.

More
8 years 11 months ago #46614 by faawrenchbndr
Replied by faawrenchbndr on topic MechArmor Defense Tac Ops Ambi Charging Handle
P

jtallen83 wrote:

faawrenchbndr wrote: Is it me or does it like like a lot of snag hazards?


They make a CQB version that is narrower for applications where that is an issue. The standard handle really doesn't stick out much more than what is needed to grab it and avoid a scope. I would say it is less snaggable(is that a word?) than the BCM 3 handle I have on my Matrix build.


May have to try one....thanks

Please Log in or Create an account to join the conversation.

More
8 years 11 months ago - 8 years 11 months ago #46806 by jtallen83
Replied by jtallen83 on topic MechArmor Defense Tac Ops Ambi Charging Handle
Just ordered the CQB version for an AR-15 build;

mechdefense.com/products/ar15-tactical-c...ng-handle-tacops-cqb

Got it and the trigger below :dance: I'll post pictures and further review when I put it to use.

mechdefense.com/products/rough-justice-3...match-trigger-for-ar
Last edit: 8 years 11 months ago by jtallen83.

Please Log in or Create an account to join the conversation.

More
8 years 11 months ago #46893 by jtallen83
Replied by jtallen83 on topic MechArmor Defense Tac Ops Ambi Charging Handle
Forgot to take pictures before I installed the trigger so the website image will have to do;

This image is hidden for guests.
Please log in or register to see it.


The fit in my AR-10 is snug with a firm contact on the safety. The pull is just crazy smooth , no creep, super crisp break, very minimal overtravel, and a VERY short reset. I'm used to two stage triggers and have always prefered them but I might just be able to get used to this one!

The CQB charging handle is just as solid and smooth as the standard with a little smaller gripping surface;

This image is hidden for guests.
Please log in or register to see it.

Please Log in or Create an account to join the conversation.